Replace Lock in UPVC Door
If you've got a upvc door lock that isn't working properly you should call in an expert locksmith. They are quick, efficient and will complete the task to a very high standard.
Changing a upvc barrel lock isn't difficult to do. You just need to know the procedure and follow the steps below.
Lock the barrel off.
uPVC windows and doors are extremely common in a variety of properties. They are ideal for letting sunlight into your home and are easy to open using the right key. Switching the barrel of a lock on a uPVC door is an easy task that takes only five minutes. It's a simple fix if you've lost your key, or if a tenant has left and not returned it, or the barrel of the lock is damaged.
You will need to remove the screws that hold the handles first. The handles will be moved out of the way to allow access to the lock barrel screws. Do not loosen the screws too quickly since this could cause damage to the handles.
Once the screws are removed After removing the screws, look for the screw that is on the inside of the door that holds the barrel lock in place. This screw stands out and is a different color to the screws on the door. Using the Phillips screwdriver, take out this screw. Take the key that you use to open the lock and insert it into the barrel. Turn it to the right as much as possible. This should release the barrel and make it easier to pull it out of the door.
Now that you have loosened the screw, it's time to break the pins holding the euro cylinder in place. To do this, you will require pliers that are strong or mole grips. Grab the protruding end of the euro cylinder, and bend it from side to side, and then up and down. This will break the two support pins that are holding it in place.
Once the old cylinder is gone, you can start the process of installing the new one. First, you will need to determine the size of the lock cylinder to ensure that you have purchased the right replacement. This can be done by measuring the distance between the middle of the circular keyhole and the center square spindle. The measurement should be taken at the upper spindle.
Change the Cylinder
The main locking mechanism is an euro cylinder. These are easy to change and don't need an expert locksmith or handyman service. If yours does not have this security feature, you must replace it with one that does. These are inexpensive and can save you money and hassle in the event that your locks have been compromised.
Open the door and stand directly in the front of it. This will allow you to reach the handle retaining screws with your hand or the appropriate tool. You can loosen the screw a little, perhaps a quarter-turn to begin.
Once this is done, the cylinder should come out easily as it is no longer fixed by the screw. Next, you'll need to decide on the size of replacement cylinder you require. There are approximately 25 sizes available. It is recommended to bring your old cylinder with you when purchasing a new one so that you can be sure it will fit.
If you're not certain of the size then take a measurement from the center of the screw hole to the top of the cylinder. You can only be sure that you're purchasing the correct sized cylinders for your door made of upvc by measuring from the center of the screw hole to the end of the cylinder.
When you have your new cylinder, place it into your door in reverse to how you took out the old one. The alignment of the lock cam can be tricky however it's generally a matter of alignment.
Now you will need to screw in the long screws for securing. After this, you can check that the cylinder is securely within the door. You can now attach the handle back to the door and test it again. If all is well then the cylinder lock inside your Upvc door has been replaced and you should have added an additional layer of security to your home.
Changing the Handle
There are many reasons a door knob may become loose. This can be due to wear and tear of the handle or it can be caused by the square spindle inside the handle becoming worn or loose due to excessive use or force. In this scenario, the door handle will have to be replaced.
First, make sure the door is propped open and won't close between removing and replacing the handle. Remove the screws from the interior surface of the plate using the help of a screwdriver. This will free your handle from the plate. Be careful not to lose these screws since they will have to be re-screwed to their original position later.
You can now remove the handles to gain access to the cylinder lock inside the door. The lock will be a circular or bulb shaped cylinder that is only found in multi-point locks on upvc doors, as well as some aluminium doors. Changing the cylinder is much similar to changing the handle. The only difference is that you'll have to take the old cylinder out of the door and replace it with a new one.
When choosing the replacement handle, it is important to think about its size. The handle must be the same size as the original because it will have to be able to fit the existing screws holding the handle in place. It is best to start by looking at the size table which lists the most common sizes of replacement handle plates and their keyhole centers.
Consider upgrading your door handles made of upvc to a higher security standard such as a Sold Secure SS301 set or 2* Kitemark security handles. This will improve the security of your home and make it easier to operate your door. These sets are slightly more expensive but the added security and peace of mind is worth the cost. You don't want to push the door handle continuously up and down to open or close it.
Change the Lock
The lock on your door made of uPVC could be a weak point for burglars. Upgrade your uPVC to multipoint locking to make it more secure. This would include an open hook as well as deadbolts to deter burglars. A professional locksmith can assist you with this, but it is also possible to do the work yourself. The process is fast and easy. You'll only require some basic tools.
The first step is loosening the screws that are holding the handle. By using a screwdriver you can take the screws off and put them in a safe place. Then, you lift the handle and reveal the screw that holds the cylinder in place. The screw can be removed and replaced with a brand new one. Make sure the screw is the same size as the original. It will need to align properly with the barrel of the lock.
The process of changing the lock on your uPVC door can appear daunting. It is crucial to the security of your home. If you make mistakes, it may cause you to be unable to unlock the door. If you know how, it's quite simple and is less expensive than calling professional locksmiths.
To change the lock on your uPVC door, you will need to access the inner faceplate of the lock. You'll need to locate the screw inside the door and the retaining bolt outside the door. Once you are able to access these screws, you can remove the faceplate and replace it with a cylindrical.
It is possible to replace the lock on your uPVC door for several reasons. It could be because you lost your key, a tenant moved out but did not return the keys, or you simply need to improve the security of your home.
The process of changing a uPVC lock could be done by anyone with basic DIY skills. You'll need to check the hinges that are inside the mechanism. This can be a challenge when the lock is stuck. If double glazed window lock repair have been lubricated, it is a simple repair. If you do not feel comfortable doing this, it's best to call a professional.